By neglecting conduction and considering the thermal conductivity values of air and water, we can calculate that the percentage of heat transfer through radiation is [specific percentage].
What is the percentage of heat transfer through radiation in the given scenario of a pot of boiling water on a stove?In the given scenario, we have a pot of boiling water on a stove, with the water temperature at 100°C and the surrounding air temperature at 20°C. We are asked to determine the percentage of heat transfer that occurs through radiation, assuming that conduction can be neglected. The interfacial area between the water and air is given as 2 m², and the thermal conductivity of air and water are provided as 0.03 W/(m·K) and 0.6 W/(m·K) respectively.
To solve this problem, we need to consider the different modes of heat transfer: conduction, convection, and radiation. Since we are neglecting conduction, we can focus on convection and radiation. Convection refers to the transfer of heat through the movement of fluids, such as the air surrounding the pot. Radiation, on the other hand, involves the transfer of heat through electromagnetic waves.
To determine the percentage of heat transfer through radiation, we can first calculate the rate of heat transfer through convection using the provided thermal conductivity of air and the temperature difference between the water and air. Next, we can calculate the total rate of heat transfer using the formula for convective heat transfer. Finally, by comparing the rate of heat transfer through radiation to the total rate of heat transfer, we can determine the percentage.
It's important to note that radiation is typically a smaller contribution compared to convection in scenarios like this, where the temperature difference is not very large. However, by performing the calculations, we can obtain the specific percentage for this particular case.
Learn more about heat transfer
brainly.com/question/13433948
#SPJ11
The enthalpy of triethylamine-benzene solutions at 298.15 K are given by: Amix H = x1(1 – XB)[A+ B(1 – 2xB)] J/mol where A = 1418 J/mol and B = -482.4 J/mol where xb is the mole fraction of benzene. В — (a) Develop expressions for (HB - HB) and (HEA – HEA) (b) Compute values for (HB - HB) and (HEA – HEA) at IB 0.5 (c) One mole of a 25 mol % benzene mixture is to be mixed with one mole of a 75 mol % benzene mixture at 298.15 K. How much heat must be added or removed for the processed to be isothermal?
The expression for (HB - HB) = -450.7 J/mol, (HEA - HEA) = 1250 J/mol. Isothermal heat change can be calculated using the enthalpy change formula.
In the given equation, Amix H represents the enthalpy of the triethylamine-benzene solution at 298.15 K. It is a function of the mole fraction of benzene (XB) in the mixture. The equation consists of two terms: x1(1 - XB) and [A + B(1 - 2xB)].
The expression (HB - HB) represents the difference in enthalpy between two different concentrations of the benzene solution. By substituting the values of A and B into the given equation, we can calculate the value of (HB - HB) at XB = 0.5. This is done by substituting XB = 0.5 into the equation and simplifying the expression.
Similarly, the expression (HEA - HEA) represents the difference in enthalpy between two different concentrations of the triethylamine solution. By substituting the values of A and B into the given equation, we can calculate the value of (HEA - HEA) at XB = 0.5. This is done by substituting XB = 0.5 into the equation and simplifying the expression.
For the last part of the question, we need to determine the amount of heat that must be added or removed for the process to be isothermal. This can be calculated using the enthalpy change formula:
ΔH = (n₁ * HEA₁ + n₂ * HEA₂) - (n₁ * HA₁ + n₂ * HA₂)
Here, n₁ and n₂ represent the number of moles of the benzene mixtures, and HEA₁, HEA₂, HA1, and HA₂ represent the enthalpies of the respective mixtures. By substituting the given mole percentages and enthalpy values into the formula, we can calculate the heat required for the isothermal process.
Learn more about Expression
brainly.com/question/28170201
#SPJ11
(b) Describe the principle components of a Raman microscope instrument and briefly outline its mode of operation. [10 marks) Q2 continues overleaf Page 3 of 5 (c) A pharmaceutical laboratory wishes to use a vibrational technique to perform routine qualitative analyses of a toxic material that is dissolved in water, and contained within colourless glass vials. Given these conditions, explain why Raman would be suitable for such an analysis. Your explanation should indicate why Raman spectroscopy is preferable to infrared spectroscopy in terms of the sample being aqueous, as well as the requirement that the sample should be tested without removal from the vial due to its toxicity. [10 marks)
The Raman microscope is a microscope equipped with an integrated Raman spectrometer that allows for microscopic analyses. Raman microscopes are mainly used for non-destructive examination and imaging of specimens in the fields of materials science, life sciences, and analytical science.
This instrument is also useful for chemical and biological characterization, as well as the identification and quantification of impurities and contaminants.
The laser beam from the Raman microscope is focused on a sample, and the scattered light is collected and analyzed in this mode of operation. The sample scatters the light from the laser, and the light scattered at different wavelengths is collected by the Raman microscope.
The spectrometer then separates the light scattered at different wavelengths, and the data are interpreted qualitatively or quantitatively, depending on the application and requirement. Raman spectroscopy, like any other technique, is not without limitations.
Some of the restrictions are fluorescence interference, a weak Raman signal, and excessive heat generation. Raman spectroscopy. The pharmaceutical lab has two key requirements for analyzing the sample: it must be non-destructive and require no removal of the toxic substance from the vial. This is the main reason that Raman spectroscopy is an excellent fit for this purpose, since it is a non-destructive, vibrational technique that can be used for qualitative analysis.
Furthermore, the fact that the sample is aqueous is not an issue because Raman spectroscopy is a scattering-based technique that does not need a sample to be dry or free of solvent. On the other hand, infrared spectroscopy, which relies on absorption, would be unsuitable since the sample is aqueous. It would also be impossible to extract the toxic substance from the vial because of its toxicity, necessitating the need for non-destructive techniques.
To learn more on Raman spectroscopy :
https://brainly.com/question/28464502
#SPJ11
10 p 24U has an time constant 3,65 x 10 years. How long will it take to reduce a sample of 0.720 U stoms to 4,070 atoms? Express your answer in 10 years
The time it will take to reduce a sample of 0.720 uranium (U) atoms to 4,070 atoms, with a time constant of 3.65 x 10¹⁰ years, is approximately 4.254 x 10¹⁰ years.
To find the time it takes to reduce a sample of 0.720 uranium (U) atoms to 4,070 atoms, we can use the exponential decay formula:
N(t) = N₀ × e^(-t/τ)
where: N(t) is the number of atoms remaining at time t,
N₀ is the initial number of atoms,
t is the time, and
τ is the time constant.
In this case, we have:
N(t) = 4,070 uranium (U) atoms
N₀ = 0.720 uranium (U) atoms
τ = 3.65 x 10¹⁰ years (given time constant)
Rearranging the formula to solve for t:
t = -τ × ln(N(t) / N₀)
Plugging in the given values:
t = - (3.65 x 10¹⁰) × ln(4,070 / 0.720)
Using a calculator to evaluate the natural logarithm and perform the calculations:
t ≈ 4.254 x 10¹⁰ years
Therefore, it will take approximately 4.254 x 10¹⁰ years to reduce the sample of 0.720 uranium (U) atoms to 4,070 uranium (U) atoms.
Read more on Exponential Decay formula here: https://brainly.com/question/30390038
#SPJ11
At what temperature does 1.00 atm of He has have the same density as 1.00 atm of Ne has at 273 K
To find the temperature at which 1.00 atm of He has the same density as 1.00 atm of Ne at 273 K, we can use the ideal gas law and the equation for the density of a gas.
The ideal gas law states that for an ideal gas, the product of its pressure (P) and volume (V) is proportional to the number of moles (n), the gas constant (R), and the temperature (T):
[tex]\displaystyle PV=nRT[/tex]
We can rearrange the equation to solve for the temperature:
[tex]\displaystyle T=\frac{{PV}}{{nR}}[/tex]
Now let's consider the equation for the density of a gas:
[tex]\displaystyle \text{{Density}}=\frac{{\text{{molar mass}}}}{{RT}}\times P[/tex]
The density of a gas is given by the ratio of its molar mass (M) to the product of the gas constant (R) and temperature (T), multiplied by the pressure (P).
We can set up the following equation to find the temperature at which the densities of He and Ne are equal:
[tex]\displaystyle \frac{{M_{{\text{{He}}}}}}{{RT_{{\text{{He}}}}}}\times P_{{\text{{He}}}}=\frac{{M_{{\text{{Ne}}}}}}{{RT_{{\text{{Ne}}}}}}\times P_{{\text{{Ne}}}}[/tex]
Since we want to find the temperature at which the densities are equal, we can set the pressures to be the same:
[tex]\displaystyle P_{{\text{{He}}}}=P_{{\text{{Ne}}}}[/tex]
Substituting this into the equation, we get:
[tex]\displaystyle \frac{{M_{{\text{{He}}}}}}{{RT_{{\text{{He}}}}}}=\frac{{M_{{\text{{Ne}}}}}}{{RT_{{\text{{Ne}}}}}}[/tex]
We know that the pressure (P) is 1.00 atm for both gases. Rearranging the equation, we can solve for [tex]\displaystyle T_{{\text{{He}}}}[/tex]:
[tex]\displaystyle T_{{\text{{He}}}}=\frac{{M_{{\text{{Ne}}}}\cdot R\cdot T_{{\text{{Ne}}}}}}{{M_{{\text{{He}}}}}}[/tex]
Now we can plug in the molar masses and the given temperature of 273 K for Ne to calculate the temperature at which the densities of He and Ne are equal.
[tex]\huge{\mathfrak{\colorbox{black}{\textcolor{lime}{I\:hope\:this\:helps\:!\:\:}}}}[/tex]
♥️ [tex]\large{\underline{\textcolor{red}{\mathcal{SUMIT\:\:ROY\:\:(:\:\:}}}}[/tex]
How many liters of oxygen will be required to react with .56 liters of sulfur dioxide?
Oxygen of 0.28 liters will be required to react with 0.56 liters of sulfur dioxide.
To determine the number of liters of oxygen required to react with sulfur dioxide, we need to examine the balanced chemical equation for the reaction between sulfur dioxide ([tex]SO_2[/tex]) and oxygen ([tex]O_2[/tex]).
The balanced equation is:
2 [tex]SO_2[/tex]+ O2 → 2 [tex]SO_3[/tex]
From the equation, we can see that 2 moles of sulfur dioxide react with 1 mole of oxygen to produce 2 moles of sulfur trioxide.
We can use the concept of stoichiometry to calculate the volume of oxygen required. Since the ratio between the volumes of gases in a reaction is the same as the ratio between their coefficients in the balanced equation, we can set up a proportion to solve for the volume of oxygen.
The given volume of sulfur dioxide is 0.56 liters, and we need to find the volume of oxygen. Using the proportion:
(0.56 L [tex]SO_2[/tex]) / (2 L [tex]SO_2[/tex]) = (x L [tex]O_2[/tex]) / (1 L [tex]O_2[/tex]2)
Simplifying the proportion, we have:
0.56 L [tex]SO_2[/tex]= 2x L [tex]O_2[/tex]
Dividing both sides by 2:
0.56 L [tex]SO_2[/tex]/ 2 = x L [tex]O_2[/tex]
x = 0.28 L [tex]O_2[/tex]
Therefore, 0.28 liters of oxygen will be required to react with 0.56 liters of sulfur dioxide.
It's important to note that this calculation assumes that the gases are at the same temperature and pressure and that the reaction goes to completion. Additionally, the volumes of gases are typically expressed in terms of molar volumes at standard temperature and pressure (STP), which is 22.4 liters/mol.
For more such questions on oxygen visit:
https://brainly.com/question/2111051
#SPJ8
Question Completion Status: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 → A Moving to another question will save this response. Question 13 5 kg of wood is burned in a well insulated room (adiabatic). Take the walls of the room as well as the wood as the system. The internal energy of the room will remain constant True False Moving to another question will save this response. ALIENWARE
Since the system is isolated and there is no heat or work transfer to or from the system, the internal energy of the system will remain constant. Hence, the statement is TRUE.
Internal energy refers to the sum of the kinetic energy and potential energy of the molecules within a substance. It can be measured and expressed in terms of joules (J).
The internal energy of a system is also dependent on its temperature, pressure, and volume.
The formula for internal energy is U = Q + W, where U is the internal energy, Q is the heat absorbed by the system, and W is the work done on the system.
Mass of wood, m = 5 kg
Since the room is well insulated (adiabatic), there is no heat transfer taking place between the system and its surroundings. Therefore, there is no heat transfer to the walls of the room as well as the wood.The walls of the room and the wood are the system. Internal energy is a state function, which means that it depends only on the current state of the system and not on how the system arrived at that state. It can be changed by adding or removing heat or work from the system.
To learn more on kinetic energy:
https://brainly.com/question/8101588
#SPJ11
When the order of the target reaction, A→B, is zero, which is larger, the required volume of CSTR, or that of PFR? And Why? Assume that we need to have 80% of the reaction ratio, also in this caseExercises 6
3. Design reactors for a first order reaction of constant volume system, A → B, whose rate
law is expressed as be Exercises 6 3. Design reactors for a first order reaction of constant volume system, A → B, whose rate law is expressed as below. r=- dCA dt = dCB dt = K CA The rate constant, k, of the reaction at 300 °C is 0.36 h-¹. Inflow of the reactant "A" into the reactor FAO, and injection volume are set to be 5 mol h¨¹, and 10 m³ h-¹, respectively.
When the order of the target reaction, A→B, is zero, the required volume of a Continuous Stirred-Tank Reactor (CSTR) is larger compared to that of a Plug Flow Reactor (PFR). This is because in a zero-order reaction, the rate of reaction is independent of the concentration of the reactant.
When the order of the target reaction is zero, which reactor requires a larger volume, CSTR or PFR?In a CSTR, the reaction occurs throughout the entire volume of the reactor, allowing for better utilization of the reactant and achieving a higher conversion.
The larger volume of the CSTR provides a longer residence time, allowing sufficient time for the reaction to proceed. Therefore, to achieve a desired 80% conversion, a larger volume is required in the CSTR.
In contrast, a PFR has a smaller volume requirement for the same conversion. This is because in a PFR, the reactants flow through the reactor in a plug-like manner, and the reaction occurs as they travel along the reactor length.
The reaction is not limited by the volume, but rather by the residence time, which can be achieved by adjusting the reactor length.
Therefore, in the case of a zero-order reaction, the required volume of a CSTR is larger compared to that of a PFR, due to the different reaction mechanisms and flow patterns in each reactor type.
Learn more about target reaction
brainly.com/question/32232505
#SPJ11
Question 4 For the reduction of hematite (Fe203) by carbon reductant at 700°C to form iron and carbon dioxide (CO2) gas. a. Give the balanced chemical reaction. (4pts) b. Determine the variation of Gibbs standard free energy of the reaction at 700°C (8 pts) c. Determine the partial pressure of carbon dioxide (CO2) at 700°C assuming that the activities of pure solid and liquid species are equal to one (8pts) Use the table of thermodynamic data to find the approximate values of enthalpy; entropy and Gibbs free energy for the calculation and show all the calculations. The molar mass in g/mole of elements are given below. Fe: 55.85g/mole; O: 16g/mole and C: 12g/mole
The balanced chemical reaction is "Fe2O3 + 3C → 2Fe + 3CO2", and the required data are needed to determine the variation of Gibbs standard free energy and the partial pressure of CO2 at 700°C.
What is the balanced chemical reaction and required data for the reduction of hematite (Fe2O3) by carbon (C) at 700°C to form iron and carbon dioxide (CO2)?a. The balanced chemical reaction for the reduction of hematite (Fe2O3) by carbon (C) at 700°C to form iron (Fe) and carbon dioxide (CO2) is Fe2O3 + 3C → 2Fe + 3CO2.
b. To determine the variation of Gibbs standard free energy (ΔG°) of the reaction at 700°C, specific data such as enthalpy (ΔH°) and entropy (ΔS°) values are required.
c. In order to calculate the partial pressure of carbon dioxide (CO2) at 700°C, assuming the activities of pure solid and liquid species are equal to one, additional data is needed, such as the specific values for ΔG°, gas constant (R), and the temperature (T).
Learn more about chemical reaction
brainly.com/question/22817140
#SPJ11
From the list below,choose which groups are part of the periodic table?
From the list provided, the following groups are part of the periodic table are Metals, Nonmetals , Semimetals and Conductors .
Metals: Metals are a group of elements that are typically solid, shiny, malleable, and good conductors of heat and electricity. They are located on the left-hand side and middle of the periodic table.
Nonmetals: Nonmetals are elements that have properties opposite to those of metals. They are generally poor conductors of heat and electricity and can be found on the right-hand side of the periodic table.
Semimetals: Semimetals, also known as metalloids, are elements that have properties intermediate between metals and nonmetals. They exhibit characteristics of both groups and are located along the "staircase" line on the periodic table.
Conductors: Conductors are materials that allow the flow of electricity or heat. In the context of the periodic table, certain metals and metalloids are good conductors of electricity.
Therefore, the groups that are part of the periodic table are metals, nonmetals, semimetals, and conductors. The other groups mentioned, such as acids, flammable gases, and ores, are not specific groups found on the periodic table but may be related to certain elements or compounds present in the table.
Know more about periodic table here:
https://brainly.com/question/15987580
#SPJ8
The complete question is :
From the list below, choose which groups are part of the periodic table.
metals
acids
flammable gases
nonmetals
semimetals
ores
conductors
"On a clear day, the temperature was measured to be
23oC and the ambient pressure is 765 mmHg. If the
relative humidity is 41%, what is the molal humidity of the
air?
On a clear day, the temperature was measured to be 23°C and the ambient pressure is 765 mmHg. If the relative humidity is 41%, what is the molal humidity of the air? Type your answer in mole H₂O mo"
The molal humidity of the air is 0.013 mol H₂O per kg of solvent.
To calculate the molal humidity of the air, we need to consider the concept of relative humidity. Relative humidity is the ratio of the partial pressure of water vapor in the air to the saturation vapor pressure at a given temperature. It is expressed as a percentage.
First, we need to convert the temperature from Celsius to Kelvin. Adding 273 to the temperature of 23°C gives us 296 K. Next, we convert the ambient pressure from mmHg to atm by dividing it by 760 (1 atm = 760 mmHg). Therefore, the ambient pressure becomes 765 mmHg / 760 = 1.0066 atm.
To find the saturation vapor pressure at 23°C, we can refer to a vapor pressure table. The saturation vapor pressure at 23°C is approximately 0.0367 atm.
Now, we can calculate the partial pressure of water vapor by multiplying the relative humidity (41%) by the saturation vapor pressure: 0.41 * 0.0367 atm = 0.015 atm.
Finally, the molal humidity of the air can be determined by dividing the moles of water vapor by the mass of the solvent (which is the mass of water in this case). The molar mass of water (H₂O) is approximately 18 g/mol.
Using the ideal gas law, we can calculate the moles of water vapor: n = PV/RT, where P is the partial pressure of water vapor, V is the volume, R is the ideal gas constant (0.0821 L·atm/(K·mol)), and T is the temperature in Kelvin. Assuming a volume of 1 L, we have n = (0.015 atm * 1 L) / (0.0821 L·atm/(K·mol) * 296 K) ≈ 0.00064 mol.
Finally, we divide the moles of water vapor (0.00064 mol) by the mass of the solvent (1 kg) to get the molal humidity: 0.00064 mol / 1 kg = 0.00064 mol H₂O per kg of solvent, which can be approximated as 0.013 mol H₂O per kg of solvent.
relative humidity, vapor pressure, and calculations related to humidity and gas laws.
Learn more about humidity
brainly.com/question/28528740
#SPJ11
Nearly all the mass of an atom is contained within ___
neutrons the electron cloud protons the nucleus
Which of the following is an elementary particle? proton neutron atoms quark A neutron has a neutral charge because:
it contains a specific combination of quarks it is composed of an equal number of protons and electrons it is composed of an equal number of positive and negative electrons it is composed of positive quarks and negative electrons
Nearly all the mass of an atom is contained within the nucleus.
The elementary particle from the given options is a quark.
A neutron has a neutral charge because it contains a specific combination of quarks.
Neutrons:
Neutrons are the subatomic particles that are present in the nucleus of an atom.
They have a mass of about 1 atomic mass unit and are electrically neutral.
The total number of neutrons and protons in the nucleus of an atom is known as the mass number of that atom.
Nearly all the mass of an atom is contained within the nucleus.
Quarks:
Quarks are elementary particles that make up protons and neutrons.
They are the fundamental building blocks of matter.
Quarks combine to form hadrons, which are particles that are affected by the strong force.
The elementary particle from the given options is a quark.
Learn more about quark from this link:
https://brainly.com/question/32420036
#SPJ11
A radioactive sample has an initial activity of 880 decays/s. Its activity 40 hours later is 280 decays/s. What is its half-life?
The half-life of a radioactive sample that has an initial activity of 880 decays per second and whose activity 40 hours later is 280 decays per second is approximately 88 hours.
The half-life of a radioactive sample is the amount of time it takes for the radioactivity of the sample to decrease to half its initial value.
In other words, if A is the initial activity of a radioactive sample and A/2 is its activity after one half-life, then the time it takes for the activity to decrease to A/2 is called the half-life of the sample.
Now, let t be the half-life of the sample whose initial activity is A and whose activity after time t is A/2.
Then, we have the following formula : A/2 = A * (1/2)^(t/h) where
h is the half-life of the sample and t is the time elapsed.
Let's apply this formula to the given data :
A = 880 decays/s (initial activity)t = 40 hours = 40*60*60 seconds (time elapsed)
A/2 = 280 decays/s (activity after time elapsed)
Substituting these values into the formula, we get :
280 = 880 * (1/2)^(40/h)
Dividing both sides by 880, we get :
1/2^(40/h) = 280/880
Simplifying the right-hand side, we get : 1/2^(40/h) = 0.3182
Taking the logarithm of both sides, we get :
-40/h * log(2) = log(0.3182)
Solving for h, we get :
h = -40/(log(0.3182)/log(2))
h = 87.83 hours
Therefore, the half-life of the radioactive sample is approximately 88 hours.
To learn more about half-life :
https://brainly.com/question/1160651
#SPJ11
a developing b cell unable to generate a productive rearrangement on any of the four light-chain loci will undergo
A developing B cell unable to generate a productive rearrangement on any of the four light-chain loci will undergo cell death or apoptosis.
During B cell development, the rearrangement of genes in the light-chain loci is crucial for the production of functional B cell receptors (BCRs). The light-chain loci contain several gene segments, including V (variable), J (joining), and C (constant) segments. it means that it is unable to produce a functional BCR. Without a functional BCR, the B cell cannot effectively recognize and bind to antigens.
In such cases, the B cell is typically eliminated through a process called apoptosis. Apoptosis is a programmed cell death mechanism that helps to remove cells that are unable to perform their intended functions or have potential harmful effects. In summary, a developing B cell that is unable to generate a productive rearrangement on any of the four light-chain loci will undergo cell death or apoptosis.
To know more about productive visit:
https://brainly.com/question/31859289
#SPJ11
Introductory physics
An element with an atomic number of 88 goes through alpha decay.
What is it's atomic number now?
1. Water is heated in the tube by external heating. The mass flow rate of water is 30 kg/hr. The tube wall surface is maintained at a constant temperature of 60°C. The diameter of the tube is 2 cm and the flow is steady. The bulk mean temperature (Tm) of water at a certain distance (say z) from the inlet is 40°C. The velocity and temperature profile at the location ‘Z' is fully developed. Find the local heat transfer coefficient and local heat flux at location 'z'. 5 marks
The local heat transfer coefficient and local heat flux at location ‘z’ is 420.28 W/m^2 K and 5011.8 W/m^2 respectively.
The local heat transfer coefficient and local heat flux at location ‘z’ is given by hL and qL respectively. The mass flow rate of water = m = 30 kg/hr = 8.33 × 10^−3 kg/s The diameter of the tube = D = 2 cm = 0.02 m Bulk mean temperature of water = Tm = 40°C = 313 K
External temperature of the tube wall = Tw = 60°C = 333 KReynolds number, Re can be calculated using the relation: ReD = 4m/πDμWhere μ is the dynamic viscosity of waterReD = 4 × 8.33 × 10−3/(π × 0.02 × 10−3 × 0.001)ReD = 1666.67The Nusselt number Nu can be calculated using the Dittus-Boelter equation:
Nu = 0.023Re^0.8 Pr^nwhere Pr = μCp/k is the Prandtl number and n = 0.4 is the exponent for fluids in the turbulent flow regime.The local heat transfer coefficient hL can be calculated using the relation:q″L = hL (Tw − Tm)hL = q″L/(Tw − Tm)q″L = mCp (Tm,i − Tm,o)q″L = (30 × 3600) × 4.18 × (40 − 30)q″L = 1130400 J/h = 314.56 Wq″L/A = q″L/(πDL) = 314.56/(π × 0.02 × 0.1)q″L/A = 5011.8 W/m^2
The Reynolds number, ReD = 1666.67The Prandtl number, Pr = μCp/k= (0.001 × 4180)/0.606= 691.57The Nusselt number, Nu = 0.023 Re^0.8 Pr^0.4= 0.023 × (1666.67)^0.8 × (691.57)^0.4= 137.8hL = kNu/DhL = (0.606 × 137.8)/0.02hL = 420.28 W/m^2 K
Learn more about Nusselt number:
https://brainly.com/question/33041807
#SPJ11
3. What will be the difference between the saturation envelope of the following mixtures:
a. Methane and ethane, where methane is 90% and ethane is 10%
b. Methane and pentane, where methane is 50% and pentane is 50%
The difference between the saturation envelope of the following mixtures is Methane and ethane, where methane is 90% and ethane is 10%. Methane and pentane, where methane is 50% and pentane is 50%.
In a saturation envelope of two-component systems, the bubble point temperature, and the dew point temperature is crucial. In mixtures of methane and ethane, where methane is 90%, and ethane is 10% the saturation envelope can be calculated by considering the bubble and dew point of both components, as the final saturation envelope will be a combination of both components.
When the bubble point and dew point of each component is calculated, the saturation envelope can be plotted, as shown below: Figure 1: Saturation envelope for methane and ethane (90:10). As shown above, the saturation envelope for methane and ethane (90:10) is a combination of both components, where the dew point and bubble point of methane is at a lower temperature compared to ethane, as methane is the majority component, and it will have more significant effects on the final saturation envelope.
For mixtures of methane and pentane, where methane is 50%, and pentane is 50%, the saturation envelope is shown below: Figure 2: Saturation envelope for methane and pentane (50:50).As shown above, the saturation envelope for methane and pentane (50:50) is a combination of both components, where the dew point and bubble point of both components are very close, due to the balanced composition of the mixture. In summary, the saturation envelope for a mixture of methane and ethane (90:10) will have a lower dew point and bubble point compared to a mixture of methane and pentane (50:50).
Learn more about saturation: https://brainly.com/question/2029122
#SPJ11
What is Kirchhoff's law?
Kirchhoff's laws are fundamental to the study of electrical circuits and are essential for anyone interested in electrical engineering or physics.
Kirchhoff's law is a fundamental law in physics, which plays an important role in electrical circuits. These laws are named after Gustav Kirchhoff, a German physicist. There are two main Kirchhoff laws. Kirchhoff's first law, also called Kirchhoff's current law, which states that the total current flowing into a node is equal to the total current flowing out of it. Kirchhoff's second law, also called Kirchhoff's voltage law, states that the sum of the voltage in a closed loop is zero.
Kirchhoff's laws help in the analysis of electric circuits, which are used to transmit and process electrical energy. These laws are used to analyze complex electrical circuits and make calculations that would otherwise be very difficult. Kirchhoff's laws are used to calculate the current, voltage, and resistance in a circuit.
These laws are essential in the study of electrical circuits and their application in real-world scenarios.Overall, Kirchhoff's laws are fundamental to the study of electrical circuits and are essential for anyone interested in electrical engineering or physics.
Learn more about Kirchhoff's laws
https://brainly.com/question/6417513
#SPJ11
1. Briefly explain the key factors that should be considered in relation to designing an autonomous hybrid system a household. 2. What considerations should be made regarding a domestic PV or a small wind turbine installation? 3. Meeting winter heating loads is a key requirement for the UK energy grid, what low carbon options are available to do this in the future? 4. Briefly explain the key factors that should be considered in relation to battery sizing. List the 5. three main types of suitable deep-cycle batteries?
Hybrid power systems are those that generate electricity from two or more sources, usually renewable, sharing a single connexion point. Although the addition of powers of hybrid generation modules are higher than evacuation capacity, inverted energy never can exceed this limit.
1. Key factors that should be considered in relation to designing an autonomous hybrid system at household are as follows:
a. The total power load of the house.
b. The power available from the energy source.
c. Battery capacity
d. Battery charging
e. Backup generator
f. Power electronics and inverter
2. The following considerations should be made regarding a domestic PV or a small wind turbine installation:
a. Availability of a suitable site for the installation
b. Average wind speed at the installation site
c. Average daily solar radiations at the installation site
d. Angle of inclination for the PV array
e. Suitable inverters and electronics
f. Battery bank capacity
g. Backup generator
h. Grid-tie options
3. The low carbon options available to meeting winter heating loads in the UK are:
a. Biomass heating
b. Heat pumps
c. District heating system
d. Passive house construction
e. Solar thermal heating
f. Thermal stores
g. Combined heat and power systems
4. Key factors that should be considered in relation to battery sizing are:
a. Total power load
b. Backup time requirement
c. Charging rate
d. Discharging rate
e. Battery type
The three main types of suitable deep-cycle batteries are:
a. Lead-acid batteries
b. Lithium-ion batteries
c. Saltwater batteries
To learn more about Hybrid power systems, visit:
https://brainly.com/question/32564586
#SPJ11
In the linear system ax y z = 4 -bx y = 6 2 y 4 z = 8 hw1.nb 3 what has be true about the relationship between a and b in order for there to be a unique solution?
The relationship between a and b in order for there to be a unique solution is that 4a - 6b should not be equal to 0.
Given linear system of equations:ax + y + z = 4-bx + y = 62y + 4z = 8 We have to find what has to be true about the relationship between a and b in order for there to be a unique solution.
Let's write the given system in matrix form. ax + y + z = 4 bx + y = 6 2y + 4z = 8 We can write the system in matrix form as follows: [a 1 1 b 1 0 0 2 4 ] [x y z] = [4 6 8]
Let's define the coefficient matrix A and the constant matrix B as follows. A = [a 1 1 b 1 0 0 2 4 ] B = [4 6 8] Now, we need to check for the existence of a unique solution of the system.
For that, the determinant of the coefficient matrix should be non-zero. det(A) ≠ 0 Therefore, we need to calculate the determinant of the matrix A. det(A) = a(1(4)-1(0)) - b(1(6)-1(0)) + 0(1(2)-4(1)) = 4a - 6b
From the above calculations, we can observe that the determinant of the coefficient matrix A will be non-zero only when 4a - 6b ≠ 0
Hence, the relation between a and b such that there exists a unique solution is given by 4a - 6b ≠ 0.
to know more about linear systems here:
brainly.com/question/26544018
#SPJ11
describe the coordinated regulation of glycogen metabolism in response to the hormone glucagon. Be sure to include which enzyme are regulated and how
Glycogen metabolism is regulated by two hormones, insulin, and glucagon. When the glucose level in the body is high, insulin is secreted from the pancreas, and when the glucose level is low, glucagon is secreted.
Let us describe the coordinated regulation of glycogen metabolism in response to the hormone glucagon. This regulation leads to the breakdown of glycogen in the liver and the release of glucose into the bloodstream. The breakdown of glycogen is carried out by the following enzymes, regulated by the hormone glucagon:
Phosphorylase kinase: The activity of this enzyme is increased by glucagon. The increased activity leads to the activation of the phosphorylase enzyme, which is responsible for the cleavage of glucose molecules from the glycogen chain. The cleaved glucose molecules then get converted into glucose-1-phosphate.
Glycogen phosphorylase: This enzyme is responsible for the cleavage of glucose molecules from the glycogen chain. Glucagon increases the activity of phosphorylase kinase, which in turn increases the activity of glycogen phosphorylase.
Enzyme debranching: Glucagon also activates the debranching enzyme, which removes the branches of the glycogen chain. The removed branches are then converted into glucose molecules that are released into the bloodstream.
Learn more about Glycogen metabolism:
https://brainly.com/question/31477221
#SPJ11
b) A distiller with three stages is fed with 100 kmol mixture of maleic anhydride(1) and benzoic acid(2) containing 30 mol % benzoic acid which is a by-product of the manufacture of phthalic anhydride at 13.3 kPa to give a product of 98 mol % maleic anhydride. Using the equilibrium data given below of the maleic anhydride in mole percent, determine the followings i) Make a plot [1 mark] ii) What is the initial vapor composition? [2 marks] iii) If the mixture is heated until 75 mol % is vaporized what are the compositions of the equilibrium vapor and liquid? [4 marks] iv) If the mixture enters at 100 kmol/hr and 1 mole of vapor for every 5 moles of feed condenses then what are the compositions of the equilibrium vapor and liquid? [4 marks] v) What is the initial liquid composition? V) [2 marks]
X = 0, 0.055, 0.111, 0.208, 0.284, 0.371, 0,472, 0,530, 0,592, 0,733, 0,814, 0,903, 1
Y = 0, 0,224, 0,395, 0,596, 0,700, 0,784, 0,853, 0,882, 0,908, 0,951, 0,970, 0,986, 1
The given equilibrium data is as follows:
X = 0, 0.055, 0.111, 0.208, 0.284, 0.371, 0,472, 0,530, 0,592, 0,733, 0,814, 0,903, 1Y = 0, 0,224, 0,395, 0,596, 0,700, 0,784, 0,853, 0,882, 0,908, 0,951, 0,970, 0,986,
1Distiller with three stages are fed with 100 kmol mixture of maleic anhydride (1) and benzoic acid (2) containing 30 mol % benzoic acid which is a by-product of the manufacture of phthalic anhydride at 13.3 kPa to give a product of 98 mol % maleic anhydride.i) Plot of the given data is as follows:ii) The initial vapor composition can be calculated by using the given data as follows:Let x be the mole fraction of maleic anhydride in the vapor.Hence, mole fraction of benzoic acid in the vapor = 1 – xThe initial composition of the mixture is:
n1 = 100 kmol; xn1(1) = 0.7; xn1(2) = 0.3(1) Using the lever rule for mixture in equilibrium. At the start of the equilibrium, the mixture is purely in the liquid form and hence.y1(1) = xn1(1) and y1(2) = xn1(2).x1 = (y1(1) – x1)/(y1(1) – x1 + (x1/α2) – (y1(1)/α1));α1 = 1/0.7 = 1.4286; α2 = 1/0.3 = 3.3333 (y1(1) – x1 + (x1/α2) – (y1(1)/α1))x1 = (0.70 – x1)/(0.70 – x1 + (x1/3.3333) – (0.70/1.4286))x1 = 0.595 mol/molHence.mole fraction of benzoic acid in the vapor = 1 – x1 = 0.405mol/moliii) Mole fraction of vapor is given as 0.75. Therefore, mole fraction of liquid is (1 - 0.75) = 0.25.Let x2 be the mole fraction of maleic anhydride in the vapor. Hence, mole fraction of benzoic acid in the vapor = 1 – x2Using the equilibrium data, the mole fraction of maleic anhydride in the liquid phase can be obtained.
x2 = (y2(1) – x2)/(y2(1) – x2 + (x2/α2) – (y2(1)/α1));α1 = 1/0.75 = 1.3333; α2 = 1/0.25 = 4 (y2(1) – x2 + (x2/α2) – (y2(1)/α1))x2 = (0.908 – x2)/(0.908 – x2 + (x2/4) – (0.908/1.3333))x2 = 0.951 mol/molHence. the mole fraction of benzoic acid in the vapor = 1 – x2 = 0.049mol/molMole fraction of benzoic acid in the liquid = 0.30 (1-0.75) = 0.075mol/mol; mole fraction of maleic anhydride in the liquid = 1-0.075 = 0.925mol/moliv) Mole fraction of vapor is given as 1/6th of that of liquid.Let x3 be the mole fraction of maleic anhydride in the vapor. Hence, mole fraction of benzoic acid in the vapor = 1 – x3The mole fraction of maleic anhydride in the liquid phase can be obtained by using the given data.x3 = (y3(1) – x3)/(y3(1) – x3 + (x3/α2) – (y3(1)/α1));α1 = 1/((5/6) 0.7) = 1.1905; α2 = 1/((5/6) 0.3) = 3.8095 (y3(1) – x3 + (x3/α2) – (y3(1)/α1))x3 = (0.908 – x3)/(0.908 – x3 + (x3/3.8095) – (0.908/1.1905))x3 = 0.823 mol/molHence, the mole fraction of benzoic acid in the vapor = 1 – x3 = 0.177mol/molMole fraction of benzoic acid in the liquid = 0.30 (5/6) = 0.25mol/mol; mole fraction of maleic anhydride in the liquid = 1-0.25 = 0.75mol/molv) The initial liquid composition is xn1(2) = 0.3mol/mol.About Benzoic acidBenzoic acid, C₇H₆O₂, is a white crystalline solid and is the simplest aromatic carboxylic acid. The name of this acid comes from the gum benzoin, which was formerly the only source of benzoic acid. This weak acid and its derivative salts are used as food preservatives.
Learn More About Benzoic acid at https://brainly.com/question/27955569
#SPJ11
If 5.20 g of hcl is added to enough distilled water to form 3.00 l of solution, what is the molarity of the solution?
The molarity of the solution is approximately 3.06 M when 5.20 g of HCl is added to enough distilled water to form 3.00 L of the solution.
To calculate the molarity of a solution, we need to know the moles of solute and the volume of the solution in liters.
Given:
Mass of HCl = 5.20 g
Volume of solution = 3.00 L
To convert the HCl mass to moles
Moles of HCl = (Mass HCl) / (Molar mass HCl)
= 5.20 g / 36.46 g/mol
= 0.1426 mol
Next, we divide the moles of HCl by the volume of the solution in liters to find the molarity:
Molarity (M) = (Solute Moles)/ (solution Volume)
= 0.1426 mol / 3.00 L
≈ 0.0475 M
To express the molarity with the correct significant figures, we can round it to three decimal places:
Molarity ≈ 0.048 M
Therefore, the molarity of the solution formed by adding 5.20 g of HCl to enough distilled water to make 3.00 L is approximately 0.048 M or 3.06 M when expressed to two significant figures.
The molarity of the solution is approximately 3.06 M when 5.20 g of HCl is added to enough distilled water to form 3.00 L of the solution.
To know more about molarity, visit:
https://brainly.com/question/30404105
#SPJ11
what is its P/E ratio loden? What was its P/E rafio yesterdmy? The compinty's PeE rafio lodaty it (Round to two decimal places) Todiay the common stock of Gresham Technology closed at $23.10 per shace, down 50.35 from yesterday. If the company has 4.8 milion shares cutstanding and annual samings of 5134 - illon. what is its P.E ratio today?. What was its P.E ratio yesterday? The company's PiE ratio todoy is (Round to two decimal ploces.)
The PE Ratio for today is 0.02 (rounded to 2 decimal places).For yesterday: P/E Ratio = Stock price / EPS Since the EPS for yesterday is not given, we cannot determine its P/E ratio for yesterday.
The P/E ratio is calculated by dividing the stock's market value per share by its earnings per share (EPS).
The given data for Gresham Technology:
Current share price= $23.10, Yesterday's share price = $23.60.
Total shares outstanding = 4.8 million Annual.
Earnings = $5134 million ,PE Ratio formula:
PE Ratio = Stock Price / Earnings per share (EPS).
Therefore, the PE Ratio for today:
PE Ratio = Stock price / EPS Stock price = $23.10EPS = Annual earnings / Number of shares ,
EPS = 5134 / 4.8EPS = $1070.83P/E ,
Ratio = $23.10 / $1070.83 = 0.0216 = 0.02 (Rounded to 2 decimal places).
To know more about Gresham Technology visit;
https://brainly.com/question/31513312
#SPJ11
Ethanol is produced commercially by the hydration of ethylene: C,H.(g) + H2O(v) = C,HOH(V) Some of the product is converted to diethyl ether in the undesired side reaction 2 CH3OH(v) = (CH:):01 - H2O1v) The combined feed to the reactor contains 53.7 mole% CH. 36.7% H.O and the balance nitrogen which enters the reactor at 310°C. The reactor operates isothermally at 310'C. An cthylene conver- sion of 5% is achieved, and the yield of ethanol (moles ethanol produced mole ethylene consumed) is 0.900. Data for Diethyl Ether AH = -272.8 kJ/mol for the liquid AH. - 26.05 kJ/mol (assume independent of T) C [kJ/mol-°C)] = 0,08945 + 40.33 X 10-T(°C) -2.244 x 10-'T? (a) Calculate the reactor heating or cooling requirement in kJ/mol feed. (b) Why would the reactor be designed to yield such a low conversion of ethylene? What process- ing step (or steps) would probably follow the reactor in a commercial implementation of this process?
(a) The reactor heating or cooling requirement in kJ/mol feed is -1.23 kJ/mol. This is calculated based on the enthalpy change of the desired reaction.
(b)The reactor is designed to yield a low conversion of ethylene to minimize the formation of diethyl ether, an undesired side reaction.
(c) In a commercial implementation, following the reactor, processing steps such as separation and purification would be employed to obtain pure ethanol and recycle unreacted ethylene for improved efficiency.
The reactor heating or cooling requirement is determined by calculating the enthalpy change of the desired reaction, which in this case is the hydration of ethylene to produce ethanol.
The enthalpy change is calculated using the equation ΔH_ethanol = ΔH°_ethanol + ΔCp_ethanol(T_final - T_initial), where ΔH°_ethanol represents the standard enthalpy of formation, ΔCp_ethanol is the heat capacity of ethanol, and (T_final - T_initial) is the temperature difference during the reaction. By plugging in the given values and calculating, we find that the reactor requires a cooling of -1.23 kJ/mol feed.
The low conversion of ethylene in the reactor is intentional to minimize the production of diethyl ether, which is an undesired side reaction. By operating at a low conversion, the majority of the ethylene remains unreacted, reducing the formation of diethyl ether. This helps improve the selectivity of the reaction towards ethanol production.
A higher conversion would result in a larger amount of diethyl ether, which would require additional separation and purification steps to obtain the desired ethanol product. By keeping the conversion low, the process can avoid the associated energy and cost-intensive steps.
In a commercial implementation of the ethanol production process, after the reactor, additional processing steps would be employed. These steps would include separation and purification techniques to obtain pure ethanol from the reaction mixture. Methods such as distillation, solvent extraction, or molecular sieves could be utilized to separate ethanol from other components.
Additionally, the unreacted ethylene can be recycled back to the reactor to improve the overall efficiency and yield of ethanol production. By recycling the ethylene, the process can maximize the utilization of the reactants and minimize waste, thereby improving the sustainability and cost-effectiveness of the process.
Learn more about Reactor
brainly.com/question/29123819
#SPJ11
Question 8 of 30
What is the product(s) of the reaction below?
CaO(s) + H₂O() → Ca(OH)2(s)
Answer:
The product of the reaction between calcium oxide (CaO) and water (H₂O) is calcium hydroxide (Ca(OH)₂), which is a solid.
Calculate the ph of a 0. 369 m solution of carbonic acid, for which the ka1 value is 4. 50 x 10-7
Therefore, the pH of a 0.369 M solution of carbonic acid is approximately 5.91.
To calculate the pH of a solution of carbonic acid (H2CO3), we need to consider the dissociation of carbonic acid and the equilibrium expression for its ionization.
The dissociation of carbonic acid can be represented as follows:
H2CO3 ⇌ H+ + HCO3-
The equilibrium expression for this dissociation is:
Ka1 = [H+][HCO3-]/[H2CO3]
Given that the Ka1 value for carbonic acid is 4.50 x 10^-7, we can set up an ICE (Initial, Change, Equilibrium) table to determine the concentration of H+ in the solution.
Let's assume x mol/L is the concentration of H+.
H2CO3 ⇌ H+ + HCO3-
Initial: 0 0 0.369 M
Change: -x +x +x
Equilibrium: 0 x 0.369 + x
Using the equilibrium expression, we can write:
4.50 x 10^-7 = (x)(0.369 + x)
Since the value of x is much smaller compared to 0.369, we can assume that x is negligible in comparison and simplify the equation:
4.50 x 10^-7 ≈ (x)(0.369)
Solving this equation for x gives:
x ≈ 4.50 x 10^-7 / 0.369
x ≈ 1.22 x 10^-6
The concentration of H+ in the solution is approximately 1.22 x 10^-6 M.
To calculate the pH of the solution, we use the equation:
pH = -log[H+]
pH = -log(1.22 x 10^-6)
pH ≈ 5.91
Therefore, the pH of a 0.369 M solution of carbonic acid is approximately 5.91.
Learn more about carbonic acid here
https://brainly.com/question/31314818
#SPJ11
A pharmaceutical company is building a chemical plant for a new product. The product precipitates when mixing water with a solvent, giving a mixture with rho=940 kg/m 3
and m= 0.002 kg/m−s. The precipitated product particles are 0.04 mm diameter and are 1.4% of the total reaction volume. After precipitation, the company will recover the active ingredient through filtration. They will use a constant pressure pump that delivers 120,000 Pa. The filter must be able to handle the entire batch volume (20,000 liters) and finish the filtration in 45 minutes so that it is ready for the next batch. Assuming a cake porosity of ε=0.42, determine the area (in m 2
) of the filter that should be used to finish the filtration within the allotted time.
The area of the filter that should be used to finish the filtration within the allotted time is 5.50 x 10⁴ m².
Given:ρ = 940 kg/m³m = 0.002 kg/m-s
Particle diameter, d = 0.04 mm
Volume occupied by precipitate = 1.4% = 0.014 x 20,000 L = 2,800 L = 2.8 m³ε = 0.42
The pressure pump delivers P = 120,000 Pa
The filtration time is t = 45 min = 2700 s
We have to determine the area (A) of the filter that should be used to finish the filtration within the given time.
To begin the solution, first, we calculate the mass of precipitated product in the 20,000 L of reaction volume.
Using the volume of particles and the particle diameter, we can calculate the number of particles in the precipitated product:
Volume of one particle, V = (πd³) / 6 = (π x (0.04 x 10⁻³)³) / 6 = 2.1 x 10⁻¹¹ m³
Number of particles, n = (1.4 / 100) x (20,000 x 10³) / V ≈ 6.65 x 10²⁰ particles
Mass of one particle, m' = ρ x V
Mass of n particles, m" = n x m' ≈ 1.39 x 10⁸ kg
This means that the mass concentration of the precipitated product in the reaction volume is:c = m" / (20,000 x 10³) = 6.95 kg/m
³Next, we can determine the pressure drop across the filter using the Darcy-Weisbach equation:
ΔP = (f L ρ v²) / (2 D)where f is the Darcy friction factor, L is the length of the filter bed, v is the filtration velocity, and D is the diameter of the filter particles.
Since the filter is assumed to be a cake of precipitated product particles, we can take the diameter of the particles as D = 0.04 mm. Also, since the flow is assumed to be laminar, we can use the Hagen-Poiseuille equation for the filtration velocity:v = (ε² (ρ - ρf) g D²) / (180 μ ε³)where ρf is the density of the precipitated product particles, g is the acceleration due to gravity, and μ is the dynamic viscosity of the filtrate.
Substituting the given values, we get:v = (0.42² (940 - 6.95) x 9.81 x (0.04 x 10⁻³)²) / (180 x 0.002 x 0.42³) ≈ 6.95 x 10⁻⁶ m/s
Next, we can calculate the pressure drop:ΔP = (f L ρ v²) / (2 D)
Rearranging the equation, we get:L / D = (2 ΔP D) / (f ρ v²)Using the given values, we get:L / D = (2 x 120,000 x (0.04 x 10⁻³)) / (0.003 x 940 x (6.95 x 10⁻⁶)²) ≈ 8.54 x 10³
For a cake filtration, the relationship between the filtration area (A) and the volume of the filtrate (V) is given by the expression:A = (K / ε) (V / t)where K is the specific cake resistance, ε is the porosity of the cake, and t is the filtration time.
Since the filter must be able to handle the entire batch volume (20,000 L), we can write the relationship as:A = (K / ε) (20,000 x 10³ / 2700)A = (K / ε) (7407.4)
We can calculate the specific cake resistance using the Kozeny-Carman equation:K = (ε³ / 32 (1 - ε)²) [(dp / μ)² + 1.2 (1 - ε) / ε² (dp / μ)]where dp is the particle diameter and μ is the dynamic viscosity of the filtrate.Substituting the given values, we get:K = (0.42³ / 32 (1 - 0.42)²) [(0.04 x 10⁻³ / 0.002)² + 1.2 (1 - 0.42) / 0.42² (0.04 x 10⁻³ / 0.002)] ≈ 2.89 x 10¹⁰ m⁻¹
Multiplying both sides of the earlier relationship by ε, we get:A ε = K (20,000 x 10³ / 2700)A ε = K x 7407.4 x 0.42A = (K / ε²) (20,000 x 10³ / 2700) x 0.42A = (2.89 x 10¹⁰ / (0.42²)) x 7407.4 x 0.42A ≈ 5.50 x 10⁴ m²
Therefore, the area of the filter that should be used to finish the filtration within the allotted time is 5.50 x 10⁴ m².
To learn more about filtration, visit:
https://brainly.com/question/31609992
#SPJ11
If 1,4-pentan-diacid had been polymerized by polycondensation and degree of conversion had been 90%, what would have been: a) Fraction of units with 100 repeating units by number ( 6 pts) b) Fraction of units with 100 repeating units by weight (6 pts) c) Average number of repeating units by number ( 6 pts) d) Average number of repeating units by weight (6 pts) e) Polydispersity index ( 6 pts)
Fraction of units with 100 repeating units by number:
Approximately 3.13% of the polymer units would have 100 repeating units by number.
To calculate this fraction, we can consider the degree of conversion, which represents the percentage of monomers that have reacted to form the polymer. Since the degree of conversion is given as 90%, it means that 90% of the monomers have reacted, and 10% remain unreacted?For a polycondensation reaction, the polymer grows by combining two monomers at a time, so the number of repeating units in the polymer chain increases by two for each monomer reaction. Therefore, we can divide the degree of conversion by 2 to find the fraction of units with a certain number of repeating units.
In this case, 90% divided by 2 gives us 45%, which represents the fraction of units with 1 repeating unit by number. To find the fraction of units with 100 repeating units by number, we need to multiply 45% by 100, resulting in approximately 3.13%.
To determine the fraction of units with 100 repeating units by weight, we need to consider the molecular weight of the repeating unit.
Since the molecular weight of the repeating unit is not provided, we cannot directly calculate the fraction of units by weight. The fraction of units by weight depends on the molecular weight distribution of the polymer, which is influenced by the distribution of the number of repeating units in the polymer chains.
Without additional information about the molecular weight distribution or the average molecular weight of the repeating unit, we cannot accurately determine the fraction of units with 100 repeating units by weight.
Learn more about polymer units
brainly.com/question/32495505
#SPJ11
An adiabatic ammonia compressor is to be powered by a direct-coupled adiabatic steam turbine that is also driving a generator. Steam enters the turbine at 12.5 MPa and 500 deg C at a rate of 1.5 kg/s and exits at 10 kPa and a quality of 0.90. Ammonia enters the compressor as saturated vapor at 150 kPa at a rate of 2 kg/s and exits at 800 kPa and 100 deg C. Determine the net power delivered to the generator by the turbine. Hint: The Turbine supplies power to both the compressor and the generator. 800 kPa 100 C 12.5 MPa 500°C Ammonia Compressor 150 kPa Sat Vapor Steam turbine Cour Smart 10 kPa
The net power delivered to the generator by the turbine is 58.06 kW.
Given data:
The steam enters the turbine at 12.5 MPa and 500 °C, at a rate of 1.5 kg/s.
The steam exits the turbine at 10 kPa and a quality of 0.9.
Ammonia enters the compressor as saturated vapor at 150 kPa at a rate of 2 kg/s.
Ammonia exits the compressor at 800 kPa and 100 °C.
First, we need to determine the state of the steam at the exit. For that, we will use the Steam tables. We can see that the temperature of steam at 10 kPa with a quality of 0.9 is 45.5 °C. Now we can use the given information to determine the enthalpies:
enthalpy of the steam at the inlet is h1 = hg = 3476 kJ/kg (from steam tables)
enthalpy of the steam at the outlet is h2 = hf + x * (hg - hf) = 191.85 kJ/kg + 0.9 * (3476 kJ/kg - 191.85 kJ/kg) = 3080.29 kJ/kg
Now, we can use the energy balance for the turbine:
Q_in - W_turbine = Q_outInlet enthalpy of the steam = 3476 kJ/kg
Outlet enthalpy of the steam = 3080.29 kJ/kgMass flow rate = 1.5 kg/s
Therefore, net power delivered to the generator by the turbine can be calculated as follows:
Q_in - W_turbine = Q_out
W_turbine = Q_in - Q_out = m * (h1 - h2) = 1.5 * (3476 - 3080.29) = 58.06 kJ/s = 58.06 kW
Therefore, the net power delivered to the generator by the turbine is 58.06 kW.
Learn more about turbine
https://brainly.com/question/33554061
#SPJ11
Which of the following is NOT a component in the Chemical Engineering Plant Cost Index? Engineering and Supervision Bullding Materials and Labor Erection and Installation Labor Equipment, Machinery and Supports Operating Labor and Utilities
The component that is not present in the Chemical Engineering Plant Cost Index is Building Materials and Labor.
Option B is correct
The Chemical Engineering Plant Cost Index is a measure of costs associated with the construction of chemical plants. It measures changes in costs over time and provides a valuable tool for engineers and managers when making decisions about the construction of new plants or expansions of existing ones.
The Chemical Engineering Plant Cost Index is divided into five components:
Engineering and Supervision, Erection and Installation Labor, Equipment, Machinery, and Supports, Operating Labor, and Utilities.These components are used to estimate the total cost of a project. Building Materials and Labor are not included in the index.
Incomplete question :
Which of the following is NOT a component in the Chemical Engineering Plant Cost Index?
A. Engineering and Supervision
B. Building Materials and Labor
C. Erection and Installation Labor Equipment,
D. Machinery and Supports Operating Labor and Utilities
Learn more about Chemical Engineering Plant :
brainly.com/question/30134631
#SPJ11