Answer:
D. 72.9 cm/s towards the wall
check the dimensional consistencies of s =vot+1/2at2
Answer:
s is distance so it's dimensions become L.
Nd other side we have ut+1\2at^2.
as 1\2 is a constant it will have dimensions and apply the dimensions to other quantities.
on solving u will get L there also i,e ur LHS = RHS.
thus the equation is dimensionally consistent.
Explanation:
What’s the substance that is formed as the result of a chemical reaction?
A. Chemical reaction
B. Catalyst
C. Activation energy
D. Collision theory
E. Products
F. Reactants
G. Reaction rate
Answer:
d
Explanation:
The screwdriver used by an electrician has a plastic or rubber covers on them why
Answer:
Explanation:
Plastic or rubber are regarded as an insulator, and an insulator does not allow the flow of electric current through them, so the handles of screwdrivers as well as pliers that electricians use in repairing is been covered with plastic or rubber so that electric current is prevented to pass through it to the body of electricians to avoid been electrocuted as well as shock.
How is an emulsion different from other colloids?
Answer:
The difference between colloid and emulsion is that a colloid can form when any state of matter (solid, liquid or gas) combine with a liquid whereas an emulsion has two liquid components which are immiscible with each other
Explanation:
A 70-kg skier leaves a ski jump at a velocity of 14m/s. What is the skier's momentum at that instant?
a. 5 Nos
c. 980 Nos
b. 50 Nos
d. 9800 Nos
Answer: 980 N*s
Explanation:
Every day, we use electric power to run our modern appliances. Electric power transmission lines are visible examples of transportation of electricity. Power is the rate at which energy of any type is transferred. The factors that determine the consumption of electric power are both current as well as voltage. Our society depends on electricity. Using it more efficiently will mean that impact of our natural resources can be reduced.
In a domestic circuit as shown in the figure below, A room has a ceiling fan, a tube light and a filament bulb. The tube light draws 40 W, the fan 120 W and the bulb draws 60 W on an average. The tube light is kept on for 6 hours, the fan for 12 hours and the bulb for 5 hours a day. The rate of electrical energy consumed is 3.5 rupees/ unit.
i) How many units of energy are consumed only by the fan for a day?
a) 144
b) 1.44
c) 14.4
d) 0.144
ii) Identify the correct statement about the combination of the three electrical components:
a) All three are in series and applied potential across each component remains same.
b) All three are in parallel and current through each component remains same.
c) All three are in parallel and applied potential across each component remains same.
d) All three are in series and current through each component remains same.
iii) What should be the characteristics of the material used for making the safety device used to protect these appliances?
a) It should have high melting point and high resistivity.
b) It should have high melting point and low resistivity.
c) It should have low melting point and high resistivity.
d) It should have low melting point and low resistivity
iv) Which among the following equation cannot be used to calculate electric power.
a) P= VI
b) P = V2 / R
c) P = I2 R
d) P= I2 / R
v) If two more bulbs of power 80 W and 100 W are included parallel to the 60 W bulb, which bulb will consume more energy?
a) 80 W
b) 60 W
c) 100 W
d) All the bulbs will consume same energy
Answer:
BN/A (Figure not shown)ADChelp!!
A. 0.5 s
B. 1.0 s
C. 1.5 s
D. 2.0 s
Answer:
c. 1.5 s
Explanation:
i had this and i got it right
Explain how the aperture geometry relates to the
diffraction pattern.
Answer:
The answer to this question is given below in the explanation section.
Explanation:
how the aperture geometry relates to the
diffraction pattern:
Diffraction is the spreading out of waves as they pass through an aperture or around objects.it occurs when the size of the aperture or obstacle is of the same order of magnitude as the wavelength of the incident wave.For every small aperture sizes,the vast majority of the wave is blocked.For large apertures the wave passes by or through the obstacle without any significant of diffraction.
in an aperture with width smaller than the wavelength,the wave transmitted through the aperture spreads all the way around the behave like a point sources of waves.
single slit diffraction pattern
The diffraction pattern made by waves passing through a slit of width [tex]\alpha[/tex] (larger than∫) can be understood by imagining a series of point sources all in phase along the width of the slit.The waves moving directly forward are all in phase,so they from a large central maximum.
if the waves travels at an angle Ф from the normal to the slit,then there is a path difference x between the waves production at the two end of the slit.
x=a sinΦ
The path difference between the top and middle waves is λ/2 then they are exactly out of phase and cancel each other out. This happens to all consecutive pairs of waves (the ones produced by the second source from the top and the second source past the middle etc.)at the angle so there is no resultant wave at this angle.Thus a minimum is the diffraction pattern is obtained at
λ=α sinθ
Now slit can be divided into four equal sections and the pairing of sources to give destructive interference can be repeated for the top two section ,which is identical to the result of pairing off matching sources in the bottom two sections.in this case we obtained from the minimum.
λ/2=α/4 sinθ
we can divided the slit aperture into six equal sections and pair off sources in the top two divisions and then the bottom two,to give destructive interference for every matched pair.The minimum of intensity are obtained at angles
nλ = α sinθ
where n is an integer (1,2,......), but not n=0.There is a maximum of intensity in the center of the pattern. This process only gives the position of the minima,does not work for positions of the maxima,and so does not give the intensities of the maxima.
What name is given to the work done per coulomb of charge passing between two points
Answer:
One ampere is the current that flows when one coulomb of charge passes a point in a circuit in one second.
Volt is referred to the name given to the work done per coulomb of charge
passing between two points.
What is Volts?This is referred to as the standard unit for electric potential and electric
potential difference which was named after the Italian physicist Alessandro
Volta.
Volts can be calculated by :
Volts= Work done(Joules) / charges(coulombs)
= J/C.
Read more about Volts here https://brainly.com/question/518946
A 35 kg boy is riding a 65 kg go-cart. He pushes on the gas pedal, causing the cart to accelerate at 5 m/s2. Use the equation F = m × a to find the force exerted by the go-cart’s engine.
Answer:
[tex]\boxed {\boxed {\sf 500 \ Newtons }}[/tex]
Explanation:
The equation for force is given:
[tex]F=m*a[/tex]
First, we must find the total mass, which is the sum of the boy's mass and the go-cart's mass.
total mass= boy's mass + go cart's massThe boy's mass is 35 kilograms and the go cart's is 65 kilograms.
total mass= 35 kg+ 65 kg=100 kgNow we know the total mass and the acceleration.
[tex]m= 100 \ kg \\a= 5 \ m/s^2[/tex]
Substitute the values into the formula.
[tex]F=100 \ kg * 5 \ m/s^2[/tex]
Multiply.
[tex]F= 500 \ kg*m/s^2[/tex]
1 kilograms meter per square second is equal to 1 Newton.Our answer of 500 kg*m/s² is equal to 500 Newtons.[tex]F= 500 \ N[/tex]
The force exerted by the go cart engine is 500 Newtons.
Answer:
500 N
Explanation:
Your Welcome. (:
The tendency to have more confidence in judgment and decisions than one should, based on probability or past experience is __________.
A.
belief bias
B.
overconfidence
C.
confirmation bias
D.
the availability heuristic
Answer:
Its B- overconfidence
Explanation:
The tendency to have more confidence in judgment and decisions than one should is called Overconfidence
What is overconfidence?
Overconfidence is a bias in which a person's subjective confidence is his or her judgement is reliably greater then the objective accuracy of those judgments when confidence is relatively high
Hence, The tendency to have more confidence in judgment and decisions than one should is called Overconfidence
correct answer : option B)Overconfidence
Learn more about Overconfidence :
https://brainly.com/question/8748056?referrer=searchResults
#SPJ2
Please help as soon as possible!! Please!
What kind of waves are present during an earthquake? ...
What kind of energy does an unlit match have? ...
Which of these is another way to write Newton's second law of motion? ...
What is it called when light changes direction after leaving a lens? ...
How do you calculate density?
Answer:
1. The two main types of waves are body waves and surface waves. Body waves can travel through the earth's inner layers, but surface waves can only move along the surface of the planet like ripples on water. Earthquakes radiate seismic energy as both body and surface waves.
2. potential energy
3. Newton's second law of motion is F = ma, or force is equal to mass times acceleration.
4. Refraction is the bending of light
5. Density uses the formula p=m/V, or density (p) is equal to mass (m) divided by volume (V). Density is defined as mass per unit volume.
Explanation:
Which object has a net force of -68 N?
F = 31 N
F = 89 N
F, = 27 N
F=-53N
F = 53 N F-56N
F = 103 N
F = 34 N
F=-102 N
F = -27 N
F = -74 N
F=-89 N
Done
8 of 9
Answer:
5 or 6
Explanation:you
Answer:
The 3rd graph
Explanation:
The graph that says:
Fn = 27 N
Ff= -102 N
Fp= 34 N
Fg= -27 N
The engine that moves the cables for the San Francisco cable cars delivers 390.3 kW of power for each line. How long does it take for 6.5 ×10^6 J of work (about the amount of work needed to raise a partially loaded cable car up Nob Hill) to be done by this engine?
Answer:
It would take 16.7 s for the work to be done by the engine.
Explanation:
From the question, given: Power = 390.3 kW
Work to be done = 6.5 x [tex]10^{6}[/tex] J
But, power and work done with respect to time, has a relationship of:
Power = [tex]\frac{work done}{time}[/tex]
So that,
time = [tex]\frac{work done}{Power}[/tex]
Thus,
time = [tex]\frac{6.5*10^{6} }{390.3*10^{3} }[/tex]
= 16.6539
time = 16.7 s
Time required is 16.7 seconds.
Thus, it would take 16.7 s for the work to be done by the engine.
acrostic poem for cell theory. Especially theory
Answer:
In biology, cell theory is the historic scientific theory, now universally accepted, that living organisms are made up of cells, that they are the basic structural/organizational unit of all organisms, and that all cells come from pre-existing cells. Cells are the basic unit of structure in all organisms and also the basic unit of reproduction.
Explanation:
The three tenets to the cell theory are as described below:
All living organisms are composed of one or more cells.
The cell is the basic unit of structure and organization in organisms.
Cells arise from pre-existing cells.
There is no universally accepted definition of life. Some biologists consider non-cellular entities such as viruses living organisms,[1] and thus reasonably disagree with the first tenet. Throughout this article, it will lead you through the history of cell theory, how the discovery of cells was made possible, what the cell theory has become today and background information and history regarding other opposing concepts of cell theory.
———PLEASE HELP——— I NEED THE ANSWERS (ILL GIVE BRAINLIST)
Answer:
mountains, earthquakes, tsunamis
Explanation:
Find the maximum velocity possible for the person on the swing.
if someone could explain with work that would be very much appreciated since I wasn't there when this was discussed in class.
Answer:
The maximum possible speed is 4.85 m/s.
Explanation:
The Principle Of Conservation Of Mechanical Energy
In the absence of friction, the total mechanical energy is conserved. It means that :
[tex]E_m=U+K[/tex] is constant, being U the potential energy and K the kinetic energy
U=mgh
Where m is the mass of the object, g is the gravitational acceleration and h is the height from a fixed reference.
[tex]\displaystyle K=\frac{mv^2}{2}[/tex]
Where v is the speed.
When the person is at a maximum height of 2 meters, the speed is 0. Thus the mechanical energy is made only of potential energy.
Let's fix the reference for the height to the point where the person is at minimum height (1 m from the ground level). The maximum height with respect to this reference is h=2.2 m - 1 m = 1.2 m.
The potential energy is:
U = m*9.8*1.2
U = 11.76m
When the person is at the minimum (zero) height, the mechanical energy is made only of kinetic energy. Since the mechanical energy is conserved, then:
[tex]\displaystyle \frac{mv^2}{2}=11.76m[/tex]
Multiplying by 2 and simplifying by m:
[tex]v^2=2*11.76=23.52[/tex]
Solving for v:
[tex]v=\sqrt{23.52}=4.85[/tex]
[tex]\boxed{v=4.85}[/tex]
The maximum possible speed is 4.85 m/s.
When all forces act on an object what's it called?
Answer:
Gravity
Explanation:
what are the difference between conductor and insulator?
Answer:
A conductor allows energy e.g. electric charge or heat to pass through it easily. While an insulator does not let electric current or heat to travel through it.Insulators have strong molecular bonds. While molecular bonds are very weak in conductors.Insulators have very low conductivity. While in conductors, it is very high.Insulators have a very high resistance and therefore the electrons are held together very firmly. The conductors, on the other hand, have a very low resistance.Insulators do not have any electric field, neither inside nor on the surface. While in conductors, it is found on the surface and continues to be zero in the inner part of the conductor.What is the frequency of this wave?
O1
O2
O3
O4
Answer:
f = 1/t
1/1
=1
Explanation:
The frequency f = 1/T = ω/2π of the motion gives the number of complete oscillations per unit time. It is measured in units of Hertz, (1 Hz = 1/s).
PLZ HELP!! WILL MARK BRAINLIEST!!
As waves get closer to a beach they:
decrease in energy
increase in energy
decrease in height
increase in length
write the Newton's first law of motion any three examples to justify
Answer:
stationary object with no outside force will not move. With no outside forces, a moving object will not stop. An astronaut who has their screwdriver knocked into space will see the screwdriver continue on at the same speed and direction forever. There are no forces acting on the screwdriver from friction.
Please select the word from the list that best fits the definition
Calculated by angular velocity/time
Answer:
Hi... Your answer is angular acceleration
Help help help plzzz. A 15-kilogram wagon originally at rest on a level road is pulled by a rope that exerts a constant horizontal force of 45 newton's, If the frictional forces on the wagon total 15 newton's, what will be its acceleration ? *
2.0 〖m/s〗^2
4.0 〖m/s〗^2
15 〖m/s〗^2
30 〖m/s〗^2
3.0 〖m/s〗^2
Answer:
A. 2m/(s^2)
I hope it will be useful.
Musical instruments that produce sound by vibration of a stretched string
Answer:
Stringed instruments (chordophones).
Explanation:
Musical instruments that produce sound by vibration of a stretched string are called stringed instruments (chordophones).
Some examples of stringed instruments are guitar, piano, harp, violin, sitar etc.
A guitar can be defined as a musical instrument with six or twelve strings and a long fretted fingerboard that are being played using a plectrum or by strumming (plucking) with the fingers, usually in a downward direction.
Basically, a guitar is a musical instrument that produces sound through regular vibrations and as a result of this, it is used for creating uniform and melodious sounds.
Explain why can an object moves or remain
stationary if it has balanced forces acting on it
Answer:
A balanced force means that equal force is being applied to an object on opposite sides. If equal force is being applied, there will be no change in the motion of the object; it will remain stationary. A greater force needs to be applied to one side for movement to take place.
Explanation:
Hope this helps (づ｡ ◕‿‿◕｡) づ
Love ya
activity will have the LEAST effect on your level of physical fitness?
Answer:
The correct answer is option D, Using an Electric mixer ( i hope this is the correct answer to what you are talking about because you didn't have any options but i gave out almost the same question to my students.)
Explanation:
Physical fitness is assured by activities in which our body is doing some kind of physical movements or exercise. In case of “walking to work “ the body is compelled to move or walk, in case of “carrying boxes up and down stairs” lot of physical work is done in both carrying the boxes and moving up and down the stairs, in the same way in case of “shoveling snow” some physical efforts are required to shovel the snow. But in case of using a electric mixer, the only work being done is the “pressing of ON/OFF button”. Thus , "using an electric mixer" will have the LEAST effect on your level of physical fitness
how can you verify the archimedes principle?
Answer:
It is found that W1 - W2 loss in weight of solid when immersed in water is equal to the weight of the water displaced by the body. This verifies Archimedes' principle.
Objects with different masses have the same gravitational force acting
on them.
TRUE
FALSE